Default welcome msg!

Fleck 5600 Whole House Water Softener | 24,000 Grain, 8"x44" Tank, .75 Cubic Ft Softening Resin

More Views

Fleck 5600 Whole House Water Softener | 24,000 Grain, 8"x44" Tank, .75 Cubic Ft Softening Resin
 
Reviews (0)
$489.99

Availability: In stock

FREE SHIPPING IN CONTINENTAL USA!


FLECK 5600 ELECTRONIC METERED SOFTENING WATER SYSTEM
THIS SYSTEM IS PERFECT FOR 1-3 PERSON HOME WITH HIGH HARDNESS
This system includes:
ELECTRONIC metered valve
mineral Tank 8" x 44" (Black)
Brine tank
24 V  Transformer IF NEEDED
BY PASS
Dust Cover
Distributor assembly w/ lower Screen


Preloaded .75 cubic ft of UPGRADED 10% Cross Linked Cation Softening Resin

OR
Description

Details

WHOLE HOUSE WATER SOFTENERS WITH ELECTRONIC VALVE METER

The typical water softener is a mechanical appliance that's plumbed into your home's water supply system. All water softeners use the same operating principle: They trade the minerals for something else, in most cases sodium. The process is called ion exchange.

The heart of a water softener is a mineral tank. It's filled with small polystyrene beads, also known as resin or zeolite. The beads carry a negative charge. Calcium and magnesium in water both carry positive charges. This means that these minerals will cling to the beads as the hard water passes through the mineral tank. Sodium ions also have positive charges, albeit not as strong as the charge on the calcium and magnesium. In the traditional water softeners, when a very strong brine solution is flushed through a tank that has beads already saturated with calcium and magnesium, the sheer volume of the sodium ions is enough to drive the calcium and magnesium ions off the beads. Water softeners have a separate brine tank that uses common salt to create this brine solution.

In normal operation, hard water moves into the mineral tank and the calcium and magnesium ions move to the beads, replacing sodium ions. The sodium ions go into the water. Once the beads are saturated with calcium and magnesium, the unit enters a 3-phase regenerating cycle. First, the backwash phase reverses water flow to flush dirt out of the tank. In the recharge phase, the concentrated sodium-rich salt solution is carried from the brine tank through the mineral tank. The sodium collects on the beads, replacing the calcium and magnesium, which go down the drain. Once this phase is over, the mineral tank is flushed of excess brine and the brine tank is refilled

 

Sizing Your Softener:

Water hardness can be reported in "grains per gallon" (gpg), "parts per million" (ppm) or "milligrams per liter" (mg/l). Most of the industry calculates softener size using gpg. You can divide ppm and mg/l by 17.1 to obtain your hardness value in grains per gallon.

You will also need to account for the iron and manganese in your water, and a quick way to get this value is to multiply your iron and manganese concentration (in ppm or mg/l) by a factor of 4. Add this number to the hardness value you determined above. The resulting total value is similar to a "compensated" hardness value, and will better serve to size your softener.

In the example below we will use 4 people in the home and a hardness value of 10 grains per gallon, and iron concentration of 2 ppm.

Multiply 4 people in the home x 75 gallons water usage per person per day x (10 grains hardness + (2 ppm iron x 4)) = 5,400 grains of hardness to be removed per day. So with a 32,000 grain system, set capacity would be about 26,000 grains (20% lower than actual - reserve capacity), and a metered unit would regenerate approximately every 5 days (26,000 divided by 5,400), which is acceptable.

Use the formula above to adjust for the number of people actually living in your home, and your specific water hardness.

With normal to low levels of iron in your water, you can size your softener to regenerate between every 5 to 10 days. With higher levels of iron (5 mg/l and higher) and manganese (1 mg/l and higher), it's better to size a system to regenerate more frequently, in order to keep the resin bed free of accumulated deposits. In this case, a regeneration every three to five days may be required. If you have very high iron levels in your water, please contact us by email or telephone for a sizing recommendation.

ELECTRONIC METERED SOFTENING WATER SYSTEMS.

THIS SYSTEM IS GOOD FOR 1-2 PERSON HOME WITH HIGH HARDNESS .

This system includes:

ELECTRONIC metered valve

mineral Tank 8" x 44" (Black).

Gravel

Brine tank

24 V  Transformer IF NEEDED

Bypass (1" or 3/4" - please email us with needed size, 1" is default size)

Distributor assembly w/  lower Screen

 

Additional Information

Additional Information

Name Fleck 5600 Whole House Water Softener | 24,000 Grain, 8"x44" Tank, .75 Cubic Ft Softening Resin
Model Number WHWS844
UPC 818368014627
Brand Oceanic Water Systems
Item Number 28
Shipping Length 8
Shipping Width 8
Shipping Height 44
Shipping Weight 50
Reviews

Product Tags

Use spaces to separate tags. Use single quotes (') for phrases.